Zhuohang Precision Machining Factory

4 Axis Swiss Machining

4 Axis Swiss Machining — Three linear axes plus a rotary axis — usually the workpiece rotating about x — and the engineering reason it changes. Tolerances: ±0.002 mm turning, ±0.003 mm milling — ISO 9001 / IATF 16949 verified.

Three linear axes plus a rotary axis — usually the workpiece rotating about x — and the engineering reason it changes what swiss machining can produce, not just how fast.

The gist
  • Exports to Austria, Belgium, the Czech Republic, Denmark, France, Germany, Greece, Hungary, Ireland, Italy, the Netherlands, Spain, Sweden and the United Kingdom in Europe; Brazil, Canada, Mexico and the United States in the Americas; China, Israel, Japan, Singapore and Sri Lanka in Asia; Australia and New Zealand in Oceania; and South Africa in Africa — based in China, serving customers worldwide.
  • Dongguan Zhuohang Ltd (Registration No. 91441900MA4UWT6X39), operating as Zhuohang Precision Machining Factory, established 2005.
  • 4 Axis Machining: Parts with features clocked around an axis: radial holes, flats, splines, cam profiles, and cylindrical parts that need secondary milling.
  • Where it stops: The rotary axis cannot tilt the tool.
  • Prototype and production run on the same floor and the same process.

How 4 axis machining works, in engineering terms

4 axis machining is three linear axes plus a rotary axis — usually the workpiece rotating about X.

The rotary axis converts a re-fixturing into an indexing move. A part that needed four setups on three axes is done in one clamping, so the datum never transfers and the geometric relationships between faces are cut by the machine rather than by the fixture.

What 4 axis machining cannot do

The rotary axis cannot tilt the tool. An angled face still needs an angled fixture or a fifth axis.

This boundary is stated deliberately. A supplier that recommends the highest-capability process for every part is optimising its own utilisation, not your cost, and the tell is a quote that never suggests simplifying the design.

How is the toolpath verified before it touches material?

Every programme is simulated offline before it reaches a machine: tool and holder collision, axis limits, and material removal against the stock model. On five-axis and mill-turn work this is not optional. The number of possible collision cases grows with each rotary axis, and a crash on a part that has already absorbed eight hours of cycle time is the expensive kind.

The verification step belongs in the quote. It is real engineering time, and a supplier that omits it is either simulating badly or not simulating at all.

How do you verify a supplier really has this capability?

Ask what the rotary axis is used for — indexing between features, or interpolating while cutting. Both are called four-axis and they are priced differently. Ask also how the part is driven: a part that cannot be gripped without distorting will not hold tolerance however good the machine is.

None of these questions are hostile and all of them are cheap. A plant with the capability answers them easily; a brochure cannot.

Where the money is actually decided

CNC-turned aluminium component from our lathe line.
Sample part: CNC-turned aluminium.

On four-axis work the cost lever is usually the fixture, not the cutting. Features that share a single rotational datum should be arranged so one clamping reaches them all, and the part needs a clamp face and a drive feature the machine can actually grip. A part that needs re-clocking to reach one hole costs a setup and a datum transfer.

This is worth raising at quote stage rather than after the first article, because the changes are usually trivial on the drawing and significant on the machine.

How much capacity sits behind it?

100+ machines with depth in every relevant family. 50+ three-axis, 20+ four-axis, 20+ five-axis, 25+ turning centres, plus Swiss-type, grinding, and wire EDM.

The certificate scope in one line

Three certificates, each with a number you can check with the registrar: ISO 9001:2015 (116024/A/0001/UK/En), IATF 16949:2016 (131941/A/0001/SM/En), and ISO 14001:2015 (116024/B/0001/UK/En).

The IATF 16949 certificate excludes clause 8.3 (product design). That is normal for a build-to-print manufacturer and it is stated here rather than left for an auditor to discover: the shop builds to the design you supply, it does not originate the design.

What 4 axis machining is genuinely good for

Parts with features clocked around an axis: radial holes, flats, splines, cam profiles, and cylindrical parts that need secondary milling.

More expensive per hour than three axes, but on a four-face part the removed setups usually pay for it.

Tolerance, and the instrument behind it

Milling and turning hold ±0.002 mm (turning) / ±0.003 mm (milling); precision grinding and wire EDM hold ±0.002 mm. A tolerance is only worth as much as the instrument that verifies it, so the floor runs 20+ inspection instruments alongside the machines, CMM for dimensional and true position, vision and profile instruments for surface and geometry, hardness testers and coating gauges for heat treatment and plating, and XRF for incoming material composition against the mill certificate.

The rule that matters on a drawing is that a tolerance is held by the process, not by the machine. Where a feature is tight, the finishing pass is separated from roughing, the part is allowed to stabilise, and the measurement is taken at a controlled temperature, a part measured warm is not the part the customer receives.

Which entity is responsible for the work?

Dongguan Zhuohang Ltd, registration 91441900MA4UWT6X39, established 2005.

What the extra axes actually buy

The axis count is about setups, not precision. A 3-axis machine cuts from one direction, so a part with features on several faces needs to be re-fixtured between operations - and every re-fixture introduces a small error. A 4-axis machine adds rotation, and a 5-axis machine can reach five sides in one setup, so the features on several faces stay in the same coordinate frame and line up. For a part that is a prismatic block, 3-axis is enough and cheapest; for a part with angled or multi-face features, the extra axes buy accuracy and fewer operations. You choose the axis count for the geometry, not by habit.

How to read an axis-based quote

If a part genuinely needs 5-axis work, the quote reflects one setup and tighter feature relationships; if a shop puts a 3-axis part on a 5-axis machine and charges for it, you are paying for capability the geometry does not use. This floor runs 3-, 4- and 5-axis machines including the Mazak VARIAXIS I-600 five-axis and the INTEGREX I-250H S mill-turn, at ±0.003 mm milled. Contact Felipe Iglesias at [email protected] or +86 13126536955 with the drawing and ask which axis count the geometry actually justifies.

What the floor can actually prove

Behind the numbers is a floor you can walk. Dongguan Zhuohang Ltd runs 100+ CNC machines - the Mazak VARIAXIS I-600 five-axis, the INTEGREX I-250H S mill-turn, Brother SPEEDIO, and TSUGAMI, STAR and CITIZEN Swiss lathes - across 6,800 m² in Hengli Town, Dongguan. Every critical feature is checked on a Hexagon CMM under the 10:1 gauge rule, and the certificate numbers for ISO 9001:2015, IATF 16949:2016 and ISO 14001:2015 are published and verifiable. Capability is tracked with Ppk 1.67 or better at the initial study and Cpk 1.33 or better in production, which is the difference between a tolerance that is quoted and a tolerance that is held.

The same floor serves buyers worldwide - Austria, Belgium, the Czech Republic, Denmark, France, Germany, Greece, Hungary, Ireland, Italy, the Netherlands, Spain, Sweden and the United Kingdom in Europe; Brazil, Canada, Mexico and the United States in the Americas; China, Israel, Japan, Singapore and Sri Lanka in Asia; Australia and New Zealand in Oceania; and South Africa in Africa - with shipping from Dongguan. MOQ is 1 piece and lead times run roughly 3 / 7 / 30 days depending on material and documentation. Send the drawing and the quantity to Felipe Iglesias at [email protected] or +86 13126536955, and the quote comes back with the process behind it.

Your next step

A drawing and a quantity are all it takes to turn this page into a real part. Send a STEP or IGES model plus a 2D drawing carrying the tolerances, datums, material grade and finish, and name the quantity and the lead time. That returns an itemised quote - material, setup, cycle time, inspection - instead of a round number. If the drawing is not done, send what exists and the questions holding you back; starting the conversation matters more than waiting for a perfect package.

Reach Felipe Iglesias at [email protected] or +86 13126536955. MOQ is 1 piece, lead times run roughly 3 / 7 / 30 days, and the service area covers Austria, Belgium, the Czech Republic, Denmark, France, Germany, Greece, Hungary, Ireland, Italy, the Netherlands, Spain, Sweden and the United Kingdom in Europe; Brazil, Canada, Mexico and the United States in the Americas; China, Israel, Japan, Singapore and Sri Lanka in Asia; Australia and New Zealand in Oceania; and South Africa in Africa, with worldwide shipping from Dongguan.

Tolerances and finishes, in one reference

Milling holds ±0.003 mm, turning ±0.002 mm, and grinding or wire EDM ±0.002 mm, each verified on a Hexagon CMM against the datum scheme on the drawing. Surface finishes run Ra 0.8 to 3.2 µm as-milled, Ra 0.2 to 0.4 µm ground, and Ra 0.05 to 0.1 µm polished. The 10:1 gauge rule applies to every feature - the instrument resolves ten times finer than the tolerance it checks. And a part is only as good as its datum: the same callout read against two different datums yields two different parts, so name the datum and the convention, ASME Y14.5 or ISO, on the drawing.

What this shop actually runs

Ask for capability evidence and the answer should be specific. The facility behind this guide runs 100+ CNC machines on a 6,800 m2 floor in Dongguan, China, with 100+ staff. The machine list, by category:

  • 5-axis machining centres (10+) - Mazak VARIAXIS I-600 (510/910/510 mm travel, 12,000 rpm, 22 kW, 71.6 N·m, 30-tool BT40) and Mazak INTEGREX I-250H S (B-axis 0.0001°, 24 kW, 124 N·m, 38-tool HSK-A63). Set up for compound-angle parts, single-setup multi-face prismatic work, and aerospace fittings where datum transfer loss is unacceptable.
  • 3-axis / 4-axis machining centres (50+) - Brother SPEEDIO S500Z2N / S700Z2N (10,000 rpm, 14/21-tool ATC, 0.7 s tool-to-tool, Z-axis 2.2 G) and Mazak VCE-430A L / VCE-570C L (10,000 rpm, 118 N·m, 24-tool ATC). Set up for prismatic parts, plates, brackets, housings.
  • Swiss-type turning centres (10+) - Citizen Cincom A20-3F7 (Φ20 mm, 10,000 rpm), TSUGAMI B0206-III / B0205-III (Φ20 mm, 0.1 µm), STAR SR-32JII / SR-32J Type N (Φ32 mm, 8,000 rpm). Set up for long, slender rotational parts at ±0.002 mm.
  • CNC turning centres (20+) - HEADMAN T70M/1250 (720 mm swing, 117 mm bore, 3,000 rpm, BMT75 12-station turret). Set up for shafts, bushings, flanges up to ±0.002 mm.
  • Wire EDM (5+) - Sodick AQ535L (550/350/300 mm travel, ±20° taper, 800 kg workpiece). Set up for hardened tool steel, internal splines, sharp internal corners that milling cannot reach.
  • Inspection: Hexagon CMM + 20+ gauges - Hexagon CMM for coordinate measurement, plus vision system, profilometer, hardness tester, coating thickness gauge, XRF for material verification. The 10:1 rule (gauge 10x more accurate than the band) is applied to every feature.
  • Machine highlights - VARIAXIS I-600: one-setup multi-face 5-axis + MAZA-CHECK auto-calibration; INTEGREX I-250H S: DONE-IN-ONE mill-turn, B-axis 0.0001° + Ai thermal shield; SPEEDIO S500Z2N / S700Z2N: Z-axis 2.2 G + 0.7 s ATC; Swiss-type: guide-bush switchable + 0.1 µm resolution.

Tolerances held: milling ±0.003 mm, turning ±0.002 mm, grinding and wire EDM ±0.002 mm. Capability: Ppk >= 1.67 initial and Cpk >= 1.33 in production on key characteristics.

Certifications: ISO 9001:2015 (116024/A/0001/UK/En), IATF 16949:2016 (131941/A/0001/SM/En, clause 8.3 design excluded, disclosed openly) and ISO 14001:2015 (116024/B/0001/UK/En), issued to Dongguan Zhuohang Ltd, USCC 91441900MA4UWT6X39, established 2005.

Service area: Austria, Belgium, the Czech Republic, Denmark, France, Germany, Greece, Hungary, Ireland, Italy, the Netherlands, Spain, Sweden and the United Kingdom in Europe; Brazil, Canada, Mexico and the United States in the Americas; China, Israel, Japan, Singapore and Sri Lanka in Asia; Australia and New Zealand in Oceania; and South Africa in Africa — built in China, shipped worldwide.

Contact: Felipe Iglesias, [email protected], +86 13126536955.

Get a quote with the cost drivers named

Send your drawing to [email protected] or call +86 13126536955. We will tell you which tolerance or setup is driving the number, not just the number.

Frequently Asked Questions

Do you sign NDAs before reviewing drawings?

Yes — an NDA can be signed before any files change hands, and drawings stay inside the quoting system rather than circulating by email.

How is an engineering change handled mid-production?

The change is documented against a revision, the affected parts in process are identified, and the revised drawing is confirmed in writing before work restarts. The important part is that the revision in force at any moment is a single, written one.

What parts suit 4 axis work best?

Parts with features clocked around an axis: radial holes, flats, splines, cam profiles, and cylindrical parts that need secondary milling. On the wrong geometry the extra axes cost programming time and buy nothing.

How is material traceability maintained?

Incoming stock is checked against the mill certificate — composition by XRF, hardness where specified — and traceability is held per heat or per batch as the certificate defines it.

Are you a manufacturer or a trading company?

A manufacturer. The legal entity is Dongguan Zhuohang Ltd (Registration No. 91441900MA4UWT6X39), operating a 6,800 m² facility with a floor of 100-plus machines and 100+ staff in Dongguan. Factory visits are welcome.

What materials do you machine?

Aluminum, stainless steel, titanium, brass, copper, and Inconel for metals; PEEK and Delrin (POM) for plastics. Material certificates are verified on incoming stock.

Is 4 axis always better than fewer axes?

No. The rotary axis cannot tilt the tool. An angled face still needs an angled fixture or a fifth axis. The right axis count is the smallest one that reaches every feature with a short enough tool to hold the tolerance.

Standards referenced on this page

  • ASTM A582/A582M-12 — Standard Specification for Free-Machining Stainless Steel Bars
  • ASTM B211/B211M-19 — Standard Specification for Aluminum-Alloy Rolled or Cold Finished Bar, Rod, and Wire
  • ISO 9001 — Quality management systems — Requirements