Zhuohang Precision Machining Factory

Swiss Machined Titanium Parts: Design Rules, Spring-Back & Tolerances

Swiss Machined Titanium Parts: Design Rules, Spring-Back & Tolerances — Tolerances: ±0.002 mm turning, ±0.003 mm milling — ISO 9001 / IATF 16949 verified.

Titanium turns cleanly on a Swiss lathe, but the part still has to be designed for the material. Its low modulus means it springs back, thin walls chatter, and the tolerance is held by the process, not the machine.

Design rules: spring-back, wall thickness and the low modulus

Titanium turns cleanly on a Swiss lathe, but the part still has to be designed for the material. Titanium's low elastic modulus — about half of steel — means it springs back behind the cut, so a tight diameter wants a rigid setup and a finishing pass that accounts for the spring-back.

Thin walls chatter more readily in titanium, and the heat that stays at the tool means deep holes want through-coolant and a chip that evacuates. The design rules for a titanium Swiss part are not the same as for steel or aluminum.

How titanium moves, and why the tolerance is held by the process

Titanium has a lower thermal expansion than aluminum but the spring-back from its low modulus is the real dimension to control. The finishing pass is taken with the part supported rigidly, and the tolerance is held by the process — the pass sequence, the coolant and the setup — not by the machine alone.

Grade 5 and Grade 2 behave differently under the same drawing. Grade 5 work-hardens and wants a sharper edge; Grade 2 is softer and gummier. Stating the grade on the drawing lets the shop hold the tolerance the way the part needs.

Which grades suit which geometries

Grade 5 (Ti-6Al-4V) is the default for strength- and fatigue-critical parts, Grade 23 (ELI) for implants with the tightest chemistry, and Grade 2 where corrosion or weldability leads. The geometry then decides the process details — thin walls, deep holes and tight diameters each impose their own constraint.

The grade is matched to what the part must do, then to how it is cut. Choosing on machinability first is how a titanium part meets the drawing and fails in service.

GradeTypeBest forSwiss behaviour
Grade 5 (Ti-6Al-4V)Alpha-betaAerospace, medical implantsThe default; cuts hot, work-hardens
Grade 2Commercially pureCorrosion, weldments, medicalSofter, gummier; lower cutting force
Grade 23 (Ti-6Al-4V ELI)Alpha-beta ELIImplants, fatigue-criticalLike Grade 5, tighter chemistry
Grade 9 (Ti-3Al-2.5V)Near-alphaTubing, aerospaceGood formability, moderate strength

Benefits of designing for the Swiss process

STAR SR-32JM Type N Swiss-type CNC automatic lathe at Zhuohang Precision Machining Factory, Dongguan, China.

A titanium part designed for Swiss machining is one that costs less to make and ships cleaner. Walls thick enough not to chatter, holes that evacuate chips, and a tolerance that accounts for spring-back mean fewer scrapped first articles and a stable price at volume.

For you the benefit is concrete: design-for-manufacture feedback at quote stage is cheaper than a drawing change after the first article.

Applications and alternatives

Swiss-machined titanium parts serve aerospace fasteners and fittings, medical implants and instruments, and high-end automotive and sporting goods. Where titanium is not right, the alternatives are a stronger or harder alloy, or a different process; the geometry and the service, not the material alone, make the call.

What this shop actually runs

We machine every part in our own 6,800 m² plant in Dongguan, China, on 100+ CNC machines with 100+ staff. The machine list by category:

  • 5-axis machining centres (10+) - Mazak VARIAXIS I-600 (510/910/510 mm travel, 12,000 rpm, 22 kW, 71.6 N·m, 30-tool BT40) and Mazak INTEGREX I-250H S (B-axis 0.0001°, 24 kW, 124 N·m, 38-tool HSK-A63). Set up for compound-angle parts, single-setup multi-face prismatic work, and aerospace fittings where datum transfer loss is unacceptable.
  • 3-axis / 4-axis machining centres (50+) - Brother SPEEDIO S500Z2N / S700Z2N (10,000 rpm, 14/21-tool ATC, 0.7 s tool-to-tool, Z-axis 2.2 G) and Mazak VCE-430A L / VCE-570C L (10,000 rpm, 118 N·m, 24-tool ATC). Set up for prismatic parts, plates, brackets, housings.
  • Swiss-type turning centres (10+) - TSUGAMI B0206-III, TSUGAMI B0205-III, STAR SR-32JII, STAR SR-32J Type N, Citizen Cincom A20-3F7. Set up for long, slender rotational parts at ±0.002 mm.
  • CNC turning centres (20+) - Used for shafts, bushings, flanges up to ±0.002 mm.
  • Wire EDM (5+) - Sodick AQ535L (550/350/300 mm travel, ±20° taper, 800 kg workpiece). Set up for hardened tool steel, internal splines, sharp internal corners that milling cannot reach.
  • Inspection: Hexagon CMM + 20+ gauges - Hexagon CMM for coordinate measurement, plus vision system, profilometer, hardness tester, coating thickness gauge, XRF for material verification. The 10:1 rule (gauge 10x more accurate than the band) is applied to every feature.
  • Machine highlights - VARIAXIS I-600: one-setup multi-face 5-axis + MAZA-CHECK auto-calibration; INTEGREX I-250H S: DONE-IN-ONE mill-turn, B-axis 0.0001° + Ai thermal shield; SPEEDIO S500Z2N / S700Z2N: Z-axis 2.2 G + 0.7 s ATC; Swiss-type: guide-bush switchable + 0.1 µm resolution.

Tolerance: ±0.003 mm CNC milling / ±0.002 mm CNC turning / ±0.002 mm grinding and wire EDM. Capability: Ppk ≥ 1.67 initial on key characteristics, Cpk ≥ 1.33 ongoing.

Certificates: ISO 9001:2015 (116024/A/0001/UK/En), IATF 16949:2016 (131941/A/0001/SM/En, with design clause 8.3 excluded, stated openly) and ISO 14001:2015 (116024/B/0001/UK/En), issued to Dongguan Zhuohang Ltd, registration 91441900MA4UWT6X39, founded 2005.

Where we ship: Austria, Belgium, the Czech Republic, Denmark, France, Germany, Greece, Hungary, Ireland, Italy, the Netherlands, Spain, Sweden and the United Kingdom in Europe; Brazil, Canada, Mexico and the United States in the Americas; China, Israel, Japan, Singapore and Sri Lanka in Asia; Australia and New Zealand in Oceania; and South Africa in Africa — plus other countries and regions worldwide, shipped from our base in Dongguan, China.

Contact: Felipe Iglesias, [email protected], +86 13126536955.

The IATF 16949 certificate excludes clause 8.3 (product design). That is normal for a build-to-print manufacturer and it is stated here rather than left for an auditor to discover: the plant cuts to the drawings you provide, it does not originate the design.

Send a drawing and get a manufacturability read

Upload your model for a quote, or arrange a factory audit with [email protected] or +86 13126536955. Ask for Felipe Iglesias.

Frequently Asked Questions

Will my titanium part spring back?

Yes — titanium's low modulus means it springs back behind the cut. The finishing pass accounts for that, and the tolerance is held by the process.

Which grade should I specify?

Grade 5 (Ti-6Al-4V) for strength and fatigue, Grade 23 ELI for implants, Grade 2 for corrosion or weldability. The service settles the grade before machinability.

Do you certify aluminum material?

Yes. Material certificates are supplied with the parts and incoming stock is checked against the mill certificate — composition by XRF, hardness where specified. Traceability is per heat or per batch as the certificate defines it.

What tolerances can you hold?

±0.003 mm on CNC milling, ±0.002 mm on CNC turning, and ±0.002 mm where precision grinding or wire EDM is used. The achievable tolerance depends on geometry, material and datum structure, so it is confirmed per feature at quote stage.

Can I audit the factory before placing an order?

Yes — on-site and video audits are both welcome at No. 8, Shuibian Songyuan Road, Hengli Town, Dongguan, Guangdong, China 523470.

Standards referenced on this page

  • ASTM B348/B348M-21 — Standard Specification for Titanium and Titanium Alloy Bars and Billets
  • ASTM B211/B211M-19 — Standard Specification for Aluminum-Alloy Rolled or Cold Finished Bar, Rod, and Wire
  • ISO 9001 — Quality management systems — Requirements